|
Product Details:
|
| Material: | SS304 316 316L | Wire Size: | Customer Order |
|---|---|---|---|
| Mesh Thickness: | As Per Customer Design | Application: | Refinery Distillation Column |
| Mesh Density: | 144, Or As Per Requirement | Shape: | Any Shape Needed |
| High Light: | customizable wire mesh demister,304 ss wire mesh demister,refining distillation column removal demister mesh |
||
Customizable Refining distillation column removal parts wire mesh demister
Wire Mesh Demister Mist Eliminators Standard Specification
1.General introduction of wire mesh demister specification
1.1 scope
A. This standard specification covers the general requirements for the design, construction, manufacture and materials of the demister specified in the XXX project specification.
B. Exceptions or changes shown in the project specification take precedence over the requirements shown here.
1.2 references
Unless otherwise specified below, the editions and addenda of each reference document in force on the date of this standard specification shall be used. When a reference document contains other documents, the version of the document required by the reference document shall be used.
A. American Society for testing and materials (ASTM) a-478, specification for chromium nickel stainless steel and heat resistant steel braids and braids.
B. ASTM b-164, specification for nickel copper alloy rods, rods, and wires.
2.Design of wire mesh demister
2.1General
A.Size, style, thickness, configuration, and materials are specified in XXX Project Specification – Vessels.
B.Mist Eliminator styles are defined as follows:
| Style | Material |
Density lb/ft3 (kg/m3) |
Wire Diameter Inches (mm) |
| A | Metallic | 9 (144.2) | 0.011 (0.28) |
| B | Metallic | 5 (80.1) | 0.011 (0.28) |
| C | Metallic | 12 (192.2) | 0.011 (0.28) |
| D |
Polytetrafluroethylene (PTFE) |
normal | 0.012 (0.30) |
| F | Polypropylene | normal | 0.012 (0.30) |
| G | Metallic |
Variable 5 (80.1) - 9 (144.2) |
0.011 (0.28) |
| V | Metallic | Other | normal |
C.Style G is a mesh blanket having a variable knitted density. The vapor inlet section is the least dense and the outlet section the densest. Typical inlet/outlet knitted mesh densities are 5 lb/ft3 (80.1) and 9 lb/ft3 (144.2). The customer can require variable density blankets having slightly different knitted densities and wire diameters.
Style V is to be determined by the vendor, based on the process conditions provided by customer. Vendor may determine the mist eliminator type best suited to meet the mist elimination requirement. The selected style may include a mesh pad, vane or a combination of mesh & vanes. The mist eliminator may be oriented vertically, horizontally or at an angle determined by the vendor. A single pad of variable knitted density may also be applied.
2.2Construction of wire mesh demister
A.Mist Eliminators shall be fabricated in one piece or in the minimum number of sections required for insertion through the vessel manway.
B.Mesh pads shall fit tightly into the pad containment system.
C.Mesh pad layers shall not be more than 9 inches (230 mm) thick. Where more than one layer is required, joints shall be staggered.
D.One-piece circular mesh pads may be spiral in form.
2.3Supports and Grids
A.The general arrangement of Mist Eliminator supports and grids shall be as factory habit unless required by customer.
B.Final details of Mist Eliminator supports and hold down grids can also be furnished by the Mist Eliminator supplier.
C.The Mist Eliminator supplier shall furnish details of components attached to the vessel to the vessel fabricator in time to permit installation without altering the vessel fabrication schedule.
D.Each section of the mesh pad shall include a grid on each side.
E.Style G mesh pads shall be furnished with an inlet and an outlet rigid welded grid. The outlet grid and blanket outlet zone of the Style G mesh pad shall be distinctly marked “Outlet”.
F.Spiral mesh pads shall include X-type grids on both sides.
2.4Fastening Devices
As the Mist Eliminator fabricator we can supply wire ties or other devices to fasten the Mist Eliminator sections to the supports, attach the grids to their vessel supports, and where multiple layer Mist Eliminators are necessary, to secure the layers together.
3.Materials of wire mesh demister
3.1Metallic Mesh Pads
Materials for metallic Mist Eliminators are as per customer need. Type 304 or Type 316 mesh pads can be in accordance with ASTM A-478. Monel mesh pads can be in accordance with ASTM B-164.
3.2Non-metallic Mist Eliminators
Non-metallic Mist Eliminators shall be PTFE or polypropylene as specified in by customer.
3.3Supports
A.Supports welded to the vessel shall be the same material as the shell. Where the shell is lined, supports welded to the lining shall be the same material as the lining.
B.Supports not welded to the shell (e.g. beams) shall be the same material as the Mist Eliminator.
3.4Grids
A.Metallic grids can be the same material as the mesh pad
B.For non-metallic mesh pads, the grids shall be carbon steel, coated with the same material as the mesh pad.
3.5Fastening Devices
A.For metallic mesh pads the wire ties or other fastening devices shall be of the same material as the Mist Eliminator.For non-metallic mesh pads, the grids shall be carbon steel, coated with the same material as the mesh pad.
B.For non-metallic mesh pads the wire ties can be the same material as the mesh pad.
Wire Mesh Demister shipping:
Tel: 15112670997
