|Specific Area:||110||Packing Layer Height:||100mm, 150mm, 200mm|
|Plate Thickness:||0.1mm, 0.12mm, 0.15mm||Size:||As Per Order|
corrugated metal plate distillation packing,
3y distillation packing,
distillation packing 3y
3Y corrugated metal plate distillation packing specific surface area
1. Hualai corrugated metal plate distillation packing popular types. (please contact me for more custom types)
|corrugation height h||mm||24.0||11.5||8.4||6.0|
|corrugation inclination θ||(°)||30||45||30||45||30||45||30||45|
|corrugation distance 2B||mm||39.6||19.0||14.0||9.9|
|corrugation angle β||(°)||79.0||79.1||79.6||79.0|
|void fraction ε||δ=0.15mm||%||99.4||98.6||98.0||97.2|
|Perforated hole diameter d0||mm||4.5||4.5||4.0||4.0|
|Opening rate σ||%||8.5-9.5||8.5-9.5||9.0-10.0||9.0-10.0|
|radius of curvature of the top circle of corrugation angle R||mm||≤2.0||≤1.4||≤0.9||≤0.5|
Note: The influence of opening rate on the plate is not calculated
2. Hualai corrugated metal plate distillation packing manufacturing requirements
2.1 According to the requirements, punching, rolling fine grain (or rolling grain equivalent to fine grain) and corrugation of raw stainless steel belt shall be made into corrugation belt of orifice plate, and then the corrugation plate shall be cut into pieces according to different chord length on the cross section of packing plate and the requirements of packing plate assembly or block assembly.
2.2 The packing plate is composed of a number of corrugated plates arranged vertically and evenly. The corrugation angle of the two adjacent orifice plates is overlapped in the opposite direction.
2.3 According to the design of tower equipment, the packing plate can be made into a whole plate or block type. The purpose of block type is to facilitate the installation of packing. Each block size shall be able to enter the tower from the manhole for assembly. For towers with a diameter less than 800mm, they can be manufactured as a whole tray or into blocks.
2.4 The whole disc of packing shall be tightly clamped with steel belt, and the end of the hoop shall be lapped and spot welded to prevent the packing from deformation. After the upper hoop is installed, the upper edge shall be cut and reserved for the flanging before the packing is installed in the tower, and the hoop shall be made into the form of anti wall flow ring. For the block packing, the packing block close to the tower wall shall be made into the form of anti wall flow ring at the end close to the tower wall. The gap between the slits depends on the diameter of the tray, and it shall be close to the tower wall.
2.5 For block packing, block diagram shall be drawn. The packing block with the same size and specification in the drawing is called "standard block", and the packing block with other sizes is called "non-standard block".
There are three methods to construct the packing block: nailing through, spot welding and combination of both.
2.6 The packing of the whole disc or the packing blocks shall be arranged evenly, and the disc surface shall be flat without unevenness.
3. Function of Hualai corrugated metal plate structured packing in distillation column
Through the packing, the two-phase flow is upward and downward convection. Gravity is the driving force of liquid flow, and pressure difference is the driving force of gas flow. The two phase flow is mass transfer and heat transfer through the two forms of film surface and spray. The mass transfer and heat transfer of the two phases in the plate column take place in the gas-liquid mixed phase on the upper surface of the tray, on the liquid layer surface of the downcomer and on the bubbling area caused by the mass transfer elements.
4. What are the necessary conditions for high vacuum distillation column?
1) The surface area per unit volume of structured packing should be large;
2) The free volume of the liquid phase in contact with the gas phase must be large;
3) The resistance to steam should be small (i.e. the cross-sectional area of the gap should be large);
4) Chemical resistance to both liquids and vapors;
5) The density should be small;
6) The price per unit of effective area should be small
In Hualai, every year we manufacture and supply hundreds of cubic meters of metal structured packing in different models. There are many popular types and materials for option. Custom order is welcome, too! We are happy to help with what you need!
Contact Person: AnnLi